Vacuum Tubes specifically selected for C.A.T. Amplifiers and Preamplifiers...
<b>[Note orders are picked and shipped on weekends. Please take this into consideration when placing your order.]</b>

Power Output Tubes:

Power Tube Testing and Matching: For twenty years, RAM Tube Works has stood as the singular reliable source for tested and truly matched power tubes. With our computerized testing procedures we are able to provide tubes that will allow your amplifiers to function their best. In virtually every instance, RAM Tubes will easily better the performance of the original tubes in your amplifiers. RAM did the original research to discover that if both bias and transconductance are matched at a particular operating point, then the tubes will remain matched over a variety of operating points. Please request or look on the web to see our paper: The Virtues of Power Tube Matching.

Power Tube Data RAM Power Tubes are tested for the following parmaters at screen voltages of 300, 350, 400 and 450 volts to allow the use of the data for any power amplifier.

G1 Bias Negative voltage to achieve a 50 mA cathode current at a given screen voltage GM Transconductance at 50 mA cathode current in micromhos. GL Grid current in micro-amps. IG2 The G2 current in mA. IKP Multiply by 10 to get peak current in mA at G1=0 (pulse test).

Pairs of tubes are matched to 5% bias accuracy (G1 Bias) and 10% transconductance (GM). This assures low distortion and tracking of bias at different cathode currents and as the tubes age. Bias is selected at common operating screen voltages (V G2). For example, 6550s are matched with VG2=350V while EL34s and 6L6s use VG2=400V.

Our testing of large batches of tubes has produced the expected bell curve when plotting the range of their test results. It is interesting to note that tubes taken from opposite ends of the spectrum (as might happen) will result in a bias variation ratio of 2:1. In an amplifier with a single bias pot for the pair, one tube would carry 2/3 of the total current and the other tube 1/3. The 2/3 tube will obviously overheat and fail early. Distortion would be high due to the gain difference associated with unequal cathode currents. Even in amplifiers with individual bias pots, transconductance variations would cause a large increase in distortion.

Preamplifier Tubes:

Dual Triode Grading System: All RAM Tube Works dual triodes are tested and graded using our proprietary tube testing computer developed by Roger A. Modjeski. The following grades are available in all dual triode types. Super Low Noise (SLN): Quite simply the industry’s quietest tube, suitable for the finest phono stages as well as any other critical application. Our SLN tubes are within 1dB of the theoretical noise limit for that tube. Low Noise (LN): A superior tube especially tested for today’s quality line stages. Our LN tubes are within 4dB of the theoretical noise limit for that tube. Standard Grade (SG): Our most economical tube, yet still a product of selection. In fact, it easily outperforms the best tubes offered by other companies.

Preamplifier Tube Testing Data: The side panel of each tube box contains the values for the following parameters for section one and section two:

VN Noise voltage ouput in micro-volts over a bandwidth of 400 - 20K Hz. RAM Our proprietary factor for the perceived sonic noisiness and variation. MIC Microphonics, susceptability to airborne and chassis vibration. GAIN AC voltage gain at 1K Hz. PVT DC value at plate to show operation variations.

Svetlana (SED) 6550 Wing C (no longer available)
12AU7 - For CAT Preamp Line Input
Svetlana (SED) 6550 Wing C (no longer available)

12AU7 - For CAT Preamp Line Input

RAM-CAT 6550/KT88 (Matched set of 16-each)

KT120 for CAT Amplifiers (Matched Set of 16-each) by RAM Labs
RAM-CAT 6550/KT88 (Matched Set of 32-each)

KT120 for CAT Amplifiers (Matched Set of 16-each) by RAM Labs


Need assistance? Email or call 805-687-2236. Photography by VisionQuest Photography